MAN TGS 35.470 8×2-6 BL incl. body for the transport of work equipment

This structure can be mounted on a MAN 8×2 truck chassis with a near-road vehicle (FHS) and a length of 5900 mm.
Wheelbase is being built. Tires 385/55 R22.5 front, 315/60 R22.5 rear. Frame height approx.
915mm loaded.
Dimensions: Platform length: approx. 9,200 mm
Overall width: 2,550 mm
Charging edge: approx. 1030 mm loaded
Payload depending on configuration: approx. 18 tons for a total weight of 32 tons
Overall height 120mm, weight of the complete assembly approx. 4200 kg
– Ground unit manufactured as an integral frame from sheet metal sections (fine-grained steel) under
Taking into account the required build guidelines of the truck manufacturer, equipped with
BICKEL heavy-duty bottom for optimal wheel load distribution up to 5t point load.
– Complete floor plate coated with anti-slip coating.
– After the rear axles, the structure is chamfered to the end of the frame, thus the stable base is provided.
Finishing material still 20 mm above the truck frame edge.
– Front panel up to approx. FHS rain guard with sturdy corners and center supports. Padding made of
Aluminium tear-off plate and rubber bumper strip (recognized as load securing device)
– 2 bars in front between the front wall supports for attaching the rigging.
– 1 tool box on the front wall, on the right and left of the winch, lockable.
– The lighting was installed in accordance with the guidelines of truck manufacturers and the StVO
– The end supports are stable to support the impact of the approach ramps.
– LED outline light on the rear assembly.
Highlights:
– 44 Zippers 5 are embedded and welded into place. 4 rows are evenly distributed.
– In the hole bottom, up to 2.5 tons can be rammed within a radius of 30mm.

Painting:
– Radiation
– Construction: Hot-dip galvanized, ramps coated with KTL
– Painting in your house colors according to RAL 9010, excluding grille frames
Rampage:
– Overall length 4800 mm, width 750 mm, approx. 10° approach slope
– Approach ramps divided with hydraulic side shift, fully foldable, with
hydraulic extension of the overall ramp, mechanical telescopic support legs, mounted on
the division,
– Suitable for 5 to point load with galvanized wire mesh gratings.
– Emergency locking during driving, laterally. via linkage with threaded lock.
– Actuation via mechanical hand lever control on the valve block, on the side at the rear right.
– Swimming position on the ramp cylinders, electrically controlled.
– Additional extension support legs mounted on the ramp. For ramp loading and unloading.
– Shortened ramp discharge with applied ramp tip. Loading extension available.
– CE – Marking
Hydraulic:
Hydraulic support at the mounting end with movable plates Ø 250mm and warning buzzer in the
FHS.
Hydraulic system via auxiliary outlet of the truck (transmission output of the truck)
Pump 47 ltr for transmission output and oil tank 100 ltr
ComeUp HV 15000 type hydraulic winch for 6,800 kg pulling force (EN 14492-1)
Includes 27 meters of 14mm wire rope, additional rope roller window,
Wire-feed roller and 2-channel radio remote control. Incl. user manual.

Warranty:
– 24 months after the defect-free acceptance on the durability and construction of the vehicle
Construction, or trailer.
– 12 months on aggregates from suppliers that are proven by us in the event of damage.

Decrease:
– As specified by the applicable regulations.

Additional:
– 2 plastic tool boxes on the right and left in front of the drive axle. 600/450/470mm
– 1 set of emergency safety belts
– Closed stainless steel box for hydraulic block
– Hula-Flash LED at ramp tip on the left and right outside
– Original headlights FHS implemented on the front panel.
– without a border on the outer frame
– Rubber bumper strip mounted on the front panel